**Click Here for Detailed Chapter-wise Notes of PHYSICS for Class 12th, JEE & NEET.**

**Q. What happens to the drift velocity $v_{\mathrm{d}}$ of electron and to the resistance $R,$ if length of the conductor is doubled (keeping potential difference unchanged) $?$**

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**Drift velocity is $v_{d}=\frac{e E \tau}{m}=\frac{e V \tau}{m l}$ and $R=\rho 1 / \mathrm{A}$Thus,(i) When

*l*is doubled, drift velocity becomes half of the initial value.(ii) When

*l*is doubled, resistance becomes twice the initial value.

**Q. A low voltage supply from which one needs high currents must have very low internal resistance. Why ?**[NCERT]

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**since the maximum current drawn from a source$\quad(\text { cell }), I=\frac{E}{r} |$Hence, for low value of $r$, current $I$ will be high.

**Q. Is there a net field inside the cell when the circuit is closed and a steady current passes**

**through? Explain.**[NCERT]

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**When circuit is closed from outside, current flows in the direction of electrostatic field outside, and opposite to the direction of electrostatic field inside the cell. The latter fact shows that there is a net field inside the cell opposite to the electrostatic field

**Q. A high tension (HT) supply of say, $6 k V$ must have**

**a very large internal resistance. Why?**[NCERT]

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**If the circuit is shorted (accidentally), the current drawn will exceed the safety limits in case internal resistance is not large.

**Q. In a potentiometer arrangement, a cell of**[NCERT]

*emf*1.25*V*gives a balance point at 35.0 cm length of the wire. If the cell is replaced by another cell and the balance point shifts to 63.0 cm, what is the*emf*of the second cell ?**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**Here, $E_{1}=1.25 \mathrm{V} ; l_{1}=35.0 \mathrm{cm} ; l_{2}=63.0 \mathrm{cm}$$\quad$ Now $, \frac{E_{1}}{E_{2}}=\frac{l_{1}}{l_{2}}$ Or $E_{2}=E_{1} \times \frac{l_{2}}{l_{1}}=1.25 \times \frac{63.0}{35.0}=2.25 \mathrm{V}$

**Q.**A galvanometer coil has a resistance of and the metre shows full scale deflection for a current of 4

*mA*. How will convert the metre into an ammeter of range 0–6

*A*. [NCERT]

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**By using a shunt of value,

**Q. A galvanometer coil has a resistance of and the metre shows full scale deflection for a current of 3**[NCERT]

*mA*. How will you convert the metre into an voltmeter of range 0 to 18*V*?**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**By connecting a resistance in series $R=\frac{V}{I_{S}}-G=\frac{18}{3 \times 10^{-3}}-12=(6000-12) \Omega=5988 \Omega$

**Q.**The electrons drift speed is estimated to be only a few

*$m m s^{-1}$*for currents in range of a few ampere. How then is current established almost the instant a circuit is closed ?

**[NCERT]**

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**When we close the circuit, the electric field is established in the circuit instantly with the speed of electrons to flow from one end of the conductor to another end. It means, the information for the flow of current is transmitted through the propagation of electromagnetic waves (electric impulse) and not with drift velocity of the electrons.

**Q. When electrons drift in a metal from lower to higher potential, does it mean that all**

**the ‘free’ electrons of the metal are moving in the same direction ?**[NCERT]

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**When a potential difference is applied across the two ends of a metal conductor, the drifting of free electrons takes place from lower to higher potential. These drifting electrons also have thermal velocity. At an instant, each free electrons moves in a direction of resultant velocity of its thermal velocity and drift velocity, which is different for various free electrons. Hence all the free electrons in the metal conductor are not moving in the same direction.

**Q. Currents of the order of 0.1**

*A*, through the human body are fatal. What causes the**Death :heating of the body due to electric current or some thing else ?**[NCERT]

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**The cause of death of a person can not be heating. The person may receive burns if the currents are too large. The cause of death is the interference caused by external currents with the nerve processes related to our heart beating, which is basically electrical in nature. Beyond a certain limit, this interference is fatal.

**Q. Choose correct alternative**(a) Alloys of metals usually have (greater/less) resistivity than that of their constituent metals(b) Alloys usually have much (lower/higher) temperature coefficients of resistance than puremetals.(c) The resistivity of the alloy manganin is nearly independent of/increases rapidly withincrease of temperature.(d) The resistivity of a typical insulator (e.g. amber) is greater than that of a metal by a factor of the order of $\left(10^{22} / 10^{3}\right)$ [NCERT]

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**(a) Greater (b) Lower (c) Nearly independent of (d) $10^{22}$

**Q. A silver wire has a resistance of $2.1 \Omega$ at $27.5^{\circ} \mathrm{C},$ and a resistance of $2.7 \Omega$ at $100^{\circ} \mathrm{C}$. Determine the temperature coefficient of resistivity of silver?**[NCERT]

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**$R_{t}=R_{0}(1+\alpha t) \mathbf{P} R_{27.5}=R_{0}(1+27.5 \alpha)$ and $R_{100}=R_{0}(1+100 \alpha)$ $R_{27.5}=2.1 \Omega$ and $R_{100}=2.7 \Omega$ hence $\frac{1+100 \alpha}{1+27.5 \alpha}=\frac{2.7}{2.1}$ On solving we get

**Q. A heating element using nichrome connected to a 230**[NCERT]

*V*supply draws an initial current of 3.2*A*which settles after a few seconds to a steady value of 2.8*A*. What is the steady temperature of the heating element if the room temperature is $27.0^{\circ} \mathrm{C}$? Temperature coefficient of resistance of nichrome averaged over the temperature range involved is $1.70 \times 10^{-4} \circ C^{-1}$**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**When a heating element is connected to a supply, initial value of current is slightly higher than the steady value. This is so because of heating resistance of the element increases and value of current decreases. When a steady state is reached

*i.e.*heat produced is equal to heat lost to the surrounding. Temperature will not rise further.

**Q. The number density of conduction electrons in a copper conductor estimated is $8.5 \times 10^{28} \mathrm{m}^{-3}$. How long does an electron take to drift from one end of a wire 3.0**[NCERT]

*m*long to its to its other end ? The area of cross-section of the wire is $2.0 \times 10^{-6} \mathrm{m}^{2}$ and it is carrying a current of 3.0*A*.**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**

**Here, $n=8.5 \times 10^{28} \mathrm{m}^{-3} ; \quad l=3.0 \mathrm{m} ; \quad A=2.0 \times 10^{-6} \mathrm{m}^{2}$**

**$I=3.0 \mathrm{A}, t=?$**

**Q. A cell of**[NCERT]

*emf*1.5*V*and internal resistance is connected to a (non-linear) conductor whose*V–I*graph is shown in figure. Obtain graphically the current drawn from the cell and its terminal voltage.**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**We know that, $V=E-I r, \quad E=1.5$ volt, $r=0.5 \Omega$$$I r=E-V, 0.5 I=1.5-V$$Values of

*V*and

*I*satisfying above equation are

*V*(volt)

*I*(ampere)Graph of these values is a line represented by dotted lines. There is a common point between the dotted line and the graph given. This corresponds to 1volt and 1

*A*. So, the cell given supplies 1

*A*current for 1volt.

**Q. A battery of**[NCERT]

*emf*9*V*and negligible internal resistance is connected to a $3 k \Omega$ resistor. The potential drop heross a part of the resistor (between point $A$ and $B$ in figure) is measured by (i) a $20 \mathrm{k} \Omega$ voltmeter. (ii) a $1 \mathrm{k\Omega}$ voltmeter. and (iii) both the voltmeters are connected across $A B .$ In which case would you get the (i) highest, (ii) lowest reading?**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**The voltmeter, which will draw minimum current (so that potential difference across

*AB*decrease by a minimum amount), will give the highest reading.

**In case $(a), R_{V}=20 k \Omega$**

**In case $(b), R_{V}=1 k \Omega$**

**In case $(c), \frac{1}{R_{V}}=\frac{1}{20}+\frac{1}{1}=\frac{1+20}{20}$ or $R_{V}=\frac{20}{21} k \Omega$**

**(i) Since in case $(a)$, the resistance of voltmeter is maximum ( $20 k \Omega$ ) ; it will draw minimum current and hence it will give the maximum reading.**

**(ii) Since in case $(c), R_{\mathrm{v}}$ is minimum $\left(\frac{20}{21} k \Omega\right),$ it will**give lowest reading.

**Q. Storage battery of a car has an emfof 12 V. If the internal resistance of the battery is $0.4 \Omega,$ what is the maximum current that can be drawn from the battery ?**[NCERT]

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**Maximum current is drawn when external resistance is zero

*i.e.*

**Q. Six lead-acid type of secondary cells each of**[NCERT]

*emf*2.0*V*and internal resistance $0.015 \Omega$ are joined in series to provide a supply to a resistance of $8.5 \Omega$ What are the current drawn from the supply and its terminal voltage ?

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...****Sol.**Total emf of the combination $=6 \times 2 V=12$ volt**Total internal resistance $=6 \times 0.015 \Omega=0.09 \Omega$**

**External resistance of the circuit $=8.5 \Omega$**

**Total resistance of the circuit $=8.5+0.09=8.59 \Omega$**

**Current drawn, $I=\frac{12}{8.59}=1.4 A$**

**Terminal potential difference, $\mathrm{V}=12-1.4 \times 0.09$**

**$=12-0.126=11.9$ volt**

**Q. A secondary cell after long the use has an**

*emf*of 1.9*V*and a large internal resistance $380 \Omega$ of What maximum current can be drawn from the cell ? Could the cell drive the starting motor of a car ?

**is required by a motor starter for a few second. So it cannot be used in a car.**

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...****Sol.**Maximum current $=\frac{1.9}{380}=0.005 A,$ A large current**Q. Two identical cells of**[NCERT]

*emf*1.5*V*each joined in parallel provide supply to an external circuit consisting of two resistors of each joined in parallel. A very high resistance voltmeter reads the terminal voltage of the cells to be 1.4*V*. What is the internal resistance of each cell?**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**In parallel combination of cells, net

*emf*is equal to the

*emf*of either cell.

*i.e.*volt If $^{c} r^{,}$ is internal resistance of each cell, then $\frac{1}{r_{P}}=\frac{2}{r}$P $r_{P}=0.5 r$

**External resistance is $R_{P}=\frac{17}{2} \Omega=8.5 \Omega$**

**Terminal potential difference $V=1.4$ volt**

**$r_{P}=\frac{E-V}{V} R_{P}$. $\mathrm{B}$. $5 r-\frac{1.5-1.4}{1.4} \times 8.5$**

**$\mathrm{B} \quad r=\frac{17}{14} \Omega=1.2 \Omega$**

**Q. (a) A d.c. supply of 120**

*V*is connected to a large resistance*X*. A voltmeter of resistance 10

*k*W placed in series in the circuit reads 4*V*. What is the value of*X*?**(b) What do you think is the purpose in using a voltmeter, instead of an ammeter, to determine the large resistance**[NCERT]

*X*?**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**(b) If an ammeter is used, then its reading will be too small to be measured.

**Q. A galvanometer with a coil of resistance $12.0 \Omega$ shows a full scale deflection for a current of 2.5**[NCERT]

*mA*. How will you convert the galvanometer into (a) an ammeter of range 0 to 7.5*A*, (b) a voltmeter of range 0 to 10.0*V*? Determine the net resistance of the metre in each case. When an ammeter is put in a circuit, does it read (slightly) less or more than the actual current in the original circuit ? When a voltmeter is put across a part of the circuit, does it read (slightly) less or more than the original voltage drop ? Explain.**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**Now, the resistance (R) of the ammeter will beAs ammeter is used in series with the circuit, therefore, its presence will increase slightly theeffective resistance of the circuit and hence will decrease the current. Therefore, the ammeterput in the circuit will read slightly less.(b) For conversion into voltmeter, let

*R*be the resistance in series with galvanometer.As $\quad R=\frac{V}{I_{g}}-G$$\backslash R=\frac{10}{2.5 \times 10^{-3}}-12=4000-12=3988 \Omega$$\therefore \quad$ Net $\quad$ resistance of $\quad$ the voltmeter $=3988+12=4000 \Omega$A voltmeter is used in parallel with the circuit. It will also allow some current to pass through it. Due to it, the current in the circuit across the two points where voltmeter is connected decreases and hence potential difference decreases. Therefore, the voltmeter reads slightly less value.

**Q. A voltmeter reads 5.0**[NCERT]

*V*at full scale deflection and is graded according to its resistance per volt at full scale deflection as $5000 \Omega / V$ How will you convert it into a voltmeter that reads 20*V*at full scale deflection ? Will it still be graded as $5000 \Omega / V$? Will you prefer this voltmeter to one that is graded as $2000 \Omega / V ?$?**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**Resistance per volt at full scale deflection$=5000 \Omega V^{-1}$Reading of voltmeter at full scale deflection $=5 V$Hence, resistance of galvanometer,$G=5000 \times 5=25000 \Omega$ and current flowing for fullscale deflection, $I_{g}=\frac{1 \mathrm{V}}{5000 \Omega}=0.0002 \mathrm{A}$The given metre work as voltmeter for range upto$20 V,$ if a resistance $R$ is connected in series with itof value, $R=\frac{V}{I_{g}}-G=\frac{20}{0.0002}-25000$ $\mathrm{B} R=75000 \Omega$Hence, total resistance of the new voltmeter $=$$75000+25000=10^{5} \Omega$ and new grading (i.e. resistance per volt) $\frac{10^{5}}{20}=5000 \Omega V^{-1}$

**Q. You are given two resistors**[NCERT]

*X*and*Y*whose resistances are to be determined using an ammeter of resistance $0.5 \Omega$ and a voltmeter of resistance $20 \times 10^{3} \Omega$ It is known that*X*is in the range of a few ohms, while*Y*is in the range of several thousand ohms. In each case, which of the following two connections would you choose for the measurement of resistance ?**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**(i) For resistance

*X*is small;(ii) Circuit should be used to measure it.

**As $\quad$ Resistance $(X)=\frac{\text { Reading of } V}{\text { Reading of } A}$**In circuit (i) it will affect the reading of ammeter.For resistance

*X*is very large, (i) circuit should be used to measure it. As resistance

*Y*is very large in comparison to the resistance of ammeter, it does not affect the reading of ammeter.

**Q. The earth’s surface has a negative surface charge density of $10^{-9} \mathrm{Cm}^{ 2}$ . The potential difference of 400**[NCERT]

*kV*between the top of the atmosphere and the surface results (due to low conductivity of the lower atmosphere) in current of only 1800*A*over the entire globe. If there were no mechanism of sustaining atmospheric electric field; how much time (roughly) would be required to neutralise (because there is a mechanism to replenish electric charges namely the continual thunder storms and lightning in different parts of the globe) Radius of the earth$=6.37 \times 10^{6} \mathrm{m}$**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**Here, $r=6.37 \times 10^{6} \mathrm{m} ; \sigma=10^{-9} \mathrm{Cm}^{-2} ; I=1800 \mathrm{A}$Area of the globe,$A=4 \pi^{2}=4 \times 3.14 \times\left(6.37 \times 10^{6}\right)^{2}=509.64 \times 10^{12} \mathrm{m}^{2}$

**Q. (a) Estimate the average drift speed of conduction electrons in a copper wire of cross sectional area $1.0 \times 10^{-7} \mathrm{m}^{2}$ carrying a current of 1.5**[NCERT]

*A.*Assume that each copper atom constributes roughly one conduction electron. The density of copper is $9.0 \times 10^{3} \mathrm{kg} / \mathrm{m}^{3}$and its atomic mass is $63.5 u$ (b) Compare the drift speed of obtained above with, (i) Thermal speeds of copper atoms at ordinary temperatures. (ii) Speed of propagation of electric field along the conductor which causes the drift motion.**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**(a) The direction of drift velocity of conduction electrons is opposite to the electric field direction,

*i.e.*, electrons drift in the direction of increasing potential. The drift speed $v_{d}$ is given by equation$v_{d}=\frac{1}{n e A}$Now, $e=1.6 \times 10^{-19} \mathrm{C}, A=1.0 \times 10^{-7} \mathrm{m}^{2}, \mathrm{I}=1.5 \mathrm{A}$. Thedensity of conduction electrons, $n$ is equal to thenumber of atoms per cubic metre (assuming oneconduction electron per $C u$ atom as is responsiblefrom its valence electron count of one). Acubic metreof copper has mass of $9.0 \times 10^{3} \mathrm{kg}$. Since $6.0 \times 10^{23}$copper atoms have a mass of $63.5 \mathrm{g} .$(b) (i) At a temperature $T$, the thermal speed of acopper atom of mass $M$ is obtained from[ $\left.<(1 / 2) M v^{2}>=(3 / 2) k_{B} T\right]$ and is thus typically of theorder of $\sqrt{k_{B} T / M},$ where $k_{B}$ is the Boltzmannconstant. For copper at $300 K,$ this is about$2 \times 10^{2} m / s .$ This figure indicates the randomvibrational speeds of electrons is much smaller, about$10^{-5}$ times the typical thermal speed at ordinarytemperatures.(ii) An electric field travelling along the conductorhas a speed of an electromagnetic wave, namelyequal to $3.0 \times 10^{8} \mathrm{ms}^{-1}$. The drift speed is incomparison, extremely small, smaller by a factor of$10^{-11}$.

**Q. 4 cells of identical**

*emf**E*, internal resistance*r*, are connected in series to a variable resistor. The following graph shows the variation of terminal voltage of the combination with the current output**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**When $I=0,$ total emf = terminal voltage$\backslash 4 E=5.6 \mathrm{V}$ or $E=1.4 \mathrm{V}$When $I=1.0 \mathrm{A}, \mathrm{V}=\frac{2.8}{4}=0.7$Internal resistance, $r=\frac{E-V}{I}=\frac{1.4-0.7}{1.0}=0.7 \Omega$The output power is maximum, when external resistance = internal resistance = 4

*r*

**Q. Determine the current in each branch of the network shown in figure**

**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**Each branch of the network is assigned an unknown current to be determined by the application of Kirchhoff’s rules. To reduce the number of unknowns at the outset, the first rule of Kirchhoff is used at every junction to assign the unknown current in each branch. We then have three unknowns $I_{1}, I_{2}$ and $I_{3}$ which can be found by applying the second rule of Kirchhoff to three different closed loops. Kirchhoff’s second rule for the closed loop

*ADCA*gives.

**$10-4\left(I_{1}-I_{2}\right)+2\left(I_{2}+I_{3}-I_{1}\right)-I_{1}=0$**…(i)

**that is, $7 I_{1}-6 I_{2}-2 I_{3}=10$**

**For the closed loop $A B C A,$ we get**

**$10-4 I_{2}-2\left(I_{2}+I_{3}\right)-I_{1}=0$**

**that is, $I_{1}+6 I_{2}+2 I_{3}=10$**…(ii)For the closed loop $B C D E B,$ we get$5-2\left(I_{2}+I_{3}\right)-2\left(I_{2}+I_{3}-I\right)=0$that is, $21_{1}-4 I_{2}-4 I_{3}=-5$ …(iii)Equations (i), (ii) and (iii) are three simultaneous equations in three unknowns. These can be solved by the usual method to give$I_{1}=2.5 A, \quad I_{2}=\frac{5}{8} A, \quad I_{3}=1 \frac{7}{8} A$The currents in the various branches of the network are$A B: \frac{5}{8} A, C A: 2 \frac{1}{2} A, D E B: 1 \frac{7}{8} A$$A D: 1 \frac{7}{8} A, C D: 0 A, B C: 2 \frac{1}{2} A$It is easily verified that Kirchhoff’s second rule applied to the remaining closed loops does not provide any additional independent equation, that is, the above values of currents satisfy the second rule for every closed loop of the network. For example, the total voltage drop over the closed loop

*BADEB*$5 \mathrm{V}+\left(\frac{5}{8} \times 4\right) \mathrm{V}-\left(\frac{15}{8} \times 4\right) \mathrm{V}$ equal to zero, as requiredby Kirchhoff’s second rule

**Q. Figure shows a 2.0**[NCERT]

*V*potentiometer used for the determination of internal resistance of a 1.5*V*cell. The balance point of the cell in open circuit is 76.3 cm. When a resistor of $9.5 \Omega$ is used in the external circuit of the cell, the balance point shifts to 64.8 cm length of the potentiometer wire. determine the internal resistance of the cell.**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**The internal resistance of a cell,$r=\left(\frac{E-V}{V}\right) R=\frac{R\left(l_{1}-l_{2}\right)}{l_{2}} \quad=\frac{9.5(76.3-64.8)}{64.8} \Omega$$=\frac{9.5 \times 11.5}{64.8}=1.686 \Omega$

**Q. Figure shows a potentiometer circuit for comparison of two resistances. The balance point with a standard resistor $R=10.0 \Omega$ is found to be 58.3 cm, while that with the unknown resistance**[NCERT]

*X*is 68.5 cm. Determine the value of*X*. What might you do if you failed to find a balance point with the given cell of*emf E*?**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**(i) Let $E_{1}$ and $E_{2}$ be the potential drops across $R$and $X$ respectively.Here, $R=10 \Omega ; l_{1}=58.3 \mathrm{cm}$ and $l_{2}=68.5 \mathrm{cm}$$\backslash \mathrm{X}=\frac{68.5}{58.3} \times 10=11.75 \Omega$(ii) We fail to get the balance point with the given cell of

*emf E*, if the potential drop across

*R*or

*X*is greater than the potential difference across the wire

*AB*. In order to obtain the balance point with the given cell

*E*, either the

*emf*of the auxiliary battery (battery connected between the terminals

*A*and

*B*) should be increased or a suitable resistance should be put in series with

*R*and

*X*(so as to decrease the potential drop across the wire

*AB*).

**Q. The four arms of a Wheatstone bridge have the following resistance**: [NCERT]

**$A B=100 \Omega, B C=10 \Omega, C D=5 \Omega,$ and $D A=60 \Omega$**

**A galvanometer of 15W resistance is connected across**

*BD.*Calculate the current through the galvanometer when a potential difference of 10*V*is maintained across*AC.***Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**Considering the mesh

*BADB*, we have$100 I_{1}+15 I_{g}-60 I_{2}=0 \quad \mathrm{P} 20 I_{1}+3 I_{g}-12 I_{2}=0 \quad \ldots(1)$Considering the mesh

*BCDB,*we have$10\left(I_{1}-I_{S}\right)-15 I_{S}-5\left(I_{2}+I_{S}\right)=0$$10 I_{1}-30 I_{S}-5 I_{2}=0 \mathrm{P} 2 I_{1}-6 I_{g}-I_{2}=0$ …(ii)Considering the mesh $A D C E A$ 60 $I_{2}+5\left(I_{2}+I_{g}\right)=10$B $65 I_{2}+5 I_{g}=10 \mathrm{P} 13 I_{2}+I_{g}=2$ …(iii)$\begin{array}{ll}{\text { Multiplying equation (ii) by } 10} \\ {20 I_{1}-60 l_{s}-10 I_{2}=0} & {\ldots \ldots(\mathrm{iv})}\end{array}$From equations (iv) and (i) we have $63 I_{g}-2 I_{2}=0$$I_{2}=31.5 I_{g}$ …(v)Substituting the value of into equation (iii), we get$13\left(31.5 I_{g}\right)+I_{g}=2 \mathrm{P} I_{g}=4.87 \mathrm{mA}$

**Q. A resistance of**[NCERT]

*R*W draw current from a potentiometer. The potentiometer has a total resistance $R_{0}$ W (figure). A voltage*V*is supplied to the potentiometer. Derive an expression for the voltage across*R*when the sliding contact is in the middle of the potentiometer.**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**While the slide is in the middle of the potentiometer only half of its resistance $\left(R_{0} / 2\right)$will be between the points

*A*and

*B*. Hence, the total resistance between

*A*and

*B*, say

*$R_{1}$*, will be given by the following expression :

**Q. A network of resistors is connected to a 16**[NCERT]

*V*battery with internal resistance of 1W, as shown in figure (a) Compute the equivalent resistance of the network. (b) Obtain the current in each resistor (c) Obtain the voltage drops $V_{A B}, V_{B C}$ and $V_{C D}$**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**The network is a simple series and parallel combination of resistors. First the two 4Wresistors in parallel are equivalent to a resistor = [(4 × 4)/(4 + 4)] W = 2WIn the same way, the 12 W and 6W resistors in parallel are equivalent to a resistor of $[(12 \times 6) /(12+6)] \Omega=4 \Omega$The equivalent resistance

*R*of the network is obtained by combining these resistors (2W and 4W) with 1W in series, that is $R=2 \Omega+4 \Omega+1 \Omega=7 \Omega$(b) The total current

*I*in the circuit is$I=\frac{E}{R+r}=\frac{16 \mathrm{V}}{(7+1) \Omega}=2 \mathrm{A}$Consider the resistors between A and B. If $I_{1}$ is thecurrent in one of the 4 W resistors and $I_{2}$ the current in the other.$I_{1} \times 4=I_{2} \times 4$ that is, $I_{1}=I_{2},$ which is otherwiseobvious from the symmetry of the two arms. But$I_{1}+I_{2}=I=2 A .$ Thus, $I_{1}=I_{2}=1 A$ that is, current ineach $4 \mathrm{W}$ resistor is $1 \mathrm{A}$. Current in $1 \mathrm{W}$ resistorbetween $\mathrm{B}$ and $\mathrm{C}$ would be $2 \mathrm{A}$.Now, consider the resistance between $\mathrm{Cand} \mathrm{D} .$ If$I_{3}$ is the current in the $12 \mathrm{W}$ resistor, and $I_{4}$ in the$6 \mathrm{W}$ resistor.$I_{3} \times 12=I_{4} \times 6,$ i.e., $I_{4}=2 I_{3}$But, $I_{3}+I_{4}=I=2 A$Thus, $I_{3}=\left(\frac{2}{3}\right) A, I_{4}=\left(\frac{4}{3}\right) A$ that is, the current in the$12 \mathrm{W}$ resistor is $(2 / 3) \mathrm{A},$ while the current in the 6Wresistor is $(4 / 3) \mathrm{A}$.(c) The voltage drop across $A B$ is$V_{A B}=I_{1} \times 4=1 A \times 4 \Omega=4 \mathrm{V}$.This can also be obtained by multiplying the total current between

*A*and

*B*by the equivalent resistance between

*A*and

*B*, that is $V_{A B}=2 A \times 2 \Omega=4 V$The voltage drop across $B C$ is $V_{B C}=2 A \times 1 \Omega=2 V$Finally, the voltage drop across $C D$ is $V_{C D}=12 \Omega \times I_{3}=12 \Omega \times\left(\frac{2}{3}\right) A=8 \mathrm{V}$This can alternately be obtained by multiplying total current between

*C*and

*D*by the equivalent resistance between

*C*and

*D*, that is $V_{C D}=2 A \times 4 \Omega=8 \mathrm{V}$Note that the total voltage drop across

*AD*is 4

*V*+ 2

*V*+8

*V*= 14

*V*. Thus, the terminal voltage of the battery is 14

*V*, while its emf is 16

*V*. The loss of the voltage (=2

*V*) is accounted for by the internal resistance 1W of the battery $[2 A \times 1 \Omega=2 \mathrm{V}]$.

**Q. A battery of 10**[NCERT]

*V*and negligible internal resistance is connected across the diagonally opposite corners of a cubical network consisting of 12 resistors each of resistance 1 W. Determine the equivalent resistance of the network and the current along each edge of the cube.**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**The network is not reducible to a simple series and parallel combinations of resistors. There is however, a clear symmetry in the problem which we can exploit to obtain the equivalent resistance of the networkThe paths

*AA’*,

*AD*and

*AB*are obviously symmetrically placed in the network. Thus, the current in each must be the same say,

*I*. Further, at the corners

*A’*,

*B*and

*D*, the incoming current

*I*must split equally into the two outgoing branches. In this manner, the current in all the 12 edges of the cube are easily written down in terms of

*I*, using Kirchhoff’s first rule and the symmetry in the problem.Next take a closed loop, say,

*ABCC’EA*, and apply Kirchhoff’s second rule.$-I R-(1 / 2) I R-I R+E=0$Where

*R*is the resistance of each edge and

*E*the

*emf*of battery. Thus, $E=\frac{5}{2} I R$The equivalent resistance $R_{\mathrm{eq}}$ of the network isFor $R=1 \Omega R_{e q}=(56 / \Omega \text { and for } E=10 \mathrm{V},$ the totalcurrent $(=3 \mathrm{I})$ in the network is$3 I=10 \mathrm{V} / 156 \mathrm{R}=12 \mathrm{A},$ i.e. $I=4 \mathrm{A}$The current flowing in each edge can now be read off from the figure\

**Q. Figure shows a potentiometer with a cell of 2.0**

*V*and internal resistance $0.40 \Omega$ maintaining a potential drop across the resistor wire*AB*. A standard cell which maintains a constant*emf*of 1.02*V*(for very moderate currents upto a few m*A*) gives a balance point at 67.3 cm length of the wire. To ensure very low currents drawn from the standard cell, a very high resistance of $600 \mathrm{k\Omega}$ is put in series with it, which is shorted close to the balance point. The standard cell is then replaced by a cell of unknown*emf**E*and the balance point found similarly, turns out to be at 82.3 cm length of the wire.**(i) What is the value**

*E*?**(ii) What purpose does the high resistance of $600 \mathrm{k\Omega}$ have?**

**(iii) Is the balance point affects by this high resistance ?**

**(iv) Is the balance point affected by the internal resistance of the driver cell ?**

**(v) Would the method work in the above situation if the driver cell of the potentiometer had an**

*emf*of 1.0*V*instead of 2.0*V*?**(vi) Would the circuit work well for determining an extremely small em.f. say of the order of a few m**[NCERT]

*V*(such as the typical*emf*of a thermo-couple) ? If not, how will you modify the circuit ?**Download eSaral App for Video Lectures, Complete Revision, Study Material and much more...**

**Sol.**(ii) It is to allow very small current to flow through the galvanometer, then the movable contactis far from the balance point.(iii) No, because there is no flow of current through the standard cell branch.(iv) No, the balance point is not affected.(v) No. If

*E*is greater than

*emf*of the driver cell of the potentiometer, there will be no balance point on the wire

*AB*.(vi) Circuit would not be suitable, because the balance point (for

*E*of the order of a few

*mV*) will be very close to the end

*A*and the percentage error in measurement will be very large.The circuit is modified by putting a suitable resistor

*R*in series with the wire

*AB*so that potential drop across

*AB*is only slightly greater than the

*emf*to be measured. Then the balance point will be at larger length of the wire and the percentage error will be much smaller.

eSaral provides you complete edge to prepare for Board and Competitive Exams like JEE, NEET, BITSAT, etc. We have transformed classroom in such a way that a student can study anytime anywhere. With the help of AI we have made the learning Personalized, adaptive and accessible for each and every one. Visit eSaral Website to download or view free study material for JEE & NEET. Also get to know about the strategies to Crack Exam in limited time period.